With this angle extrusion, your flight case will stay in one piece and is protected against bumps during transport. It is fit for wooden plates with a gauge of 10 mm.
The Penn Elcom 0491 Slam-Lid profile has a 10mm interior depth and is fully compatible with the EG-0100 angled extrusion, both in terms of finish and grooves.
Are you building a flight case for your valuable equipment? With this aluminium angle extrusion you will be able to finish it off nicely! Keep your flight case secure and protected turning transport.
Si estás construyendo una flight case para tus aparatos, con este perfil de aluminio podrás cerrar la flight case perfectamente. Perfil adecuado para un grosor de 9,5 mm.
This 1.7-metre-long rack profile is made of 3mm aluminium and features pre-drilled holes with a 9.5mm diameter.
Perfil fabricado con acero de 2 mm y una altura de 14U, con un orificio cada 15 mm, puedes montar cualquier aparato en este perfi rack.
The Penn Elcom E2215 U-shape extrusion is made of aluminium and is compatible with 9mm (3/8") thick boards, making it the ideal finishing touch for any self-built DJ furniture.
<p>This single angle extrusion by Penn Elcom is made of aluminium and has a length of 1.70 m.</p>
Si estás construyendo tu mismo una flight case y quieres que tenga unos acabados profesionales, este perfil de aluminio Penn Elcom 0522 es justo lo que necesitas.
The rack is made of 2.0mm steel and is 16 U high. As there is a hole every 15 mm, you can mount whatever device you want with this rack.
<p>The rack strip is made of 2.0 mm thick steel and has a height of 18 U. The holes have an interval of 15 mm so you are free to mount any device possible to this rack profile.</p>
The Penn Elcom 6020 aluminium rack profile is designed to complete a cage-nut based sliding system. This profile is 100cm long, 25mm wide, and 25mm deep.
This aluminium extrusion puts the clean finishing touch on any self-built flight case. The Penn Elcom 0522 is 10.2mm thick and has been grooved along the entire 1.7-metre length.
The 6108 sliding profile is easy to install in a flight case and serves to support a rack shelf or keyboard drawer. Made by Penn Elcom, so high-quality is guaranteed!
<p>This rack strip is fashioned from 2mm steel and has a height of 8 U.</p>
Si estás fabricando tu propia flight case, utiliza este perfil de aluminio para que sea lo más resistente posible. Compatible con placas de 6,8 mm de grosor.
<p>This rack strip features 9.5mm diameter punched holes at 15mm intervals. It can easily be attached to a flight case by means of its 5mm mounting holes. This rack strip is fashioned from 2.00mm steel and has a height of 2 U.</p>
This Penn Elcom double rack profile is 3U high and comes pre-drilled with holes at 15mm intervals for eased installation.
Tiene un orificio cada 15 mm, por lo que puedes montar cualquier aparato en este perfil rack. Fabricado con acero de 2 mm y una altura de 20U.
Perfil de acero 2 mm con una altura de 12U.
Este perfil tiene orificios con un diámetro de 9,5 mm cada uno. Los orificios para para fijar en la flight case tienen un diámetro de 5 mm. El perfil está fabricado de acero de 2 mm y tiene una altura de 4U.
Add several of these aluminium protective corners to your flight case to keep it held together nicely and protected against bumps during transport.
Este perfil tiene orificios con un diámetro de 9,5 mm cada uno. Los orificios para para fijar en la flight case tienen un diámetro de 5 mm. El perfil está fabricado de acero de 2 mm y tiene una altura de 6U.
<p>This rack strip is fitted with 9.5mm punched holes and has 5mm mounting holes for attachment to a flight case. This rack strip is made of 2.0mm steel and has a height of 3 U.</p>
The rack is made of 2.0mm steel and is 10 U high. As there is a hole every 15 mm, you can mount whatever device you want with this rack.
Si vas a montar tu mismo una flight case, con este perfil NC2DAE te asegurarás de que tenga acabados profesionales y de que sea duradera.
The Penn Elcom 6060 is a 1.7 metre-long aluminium rack extrusion with a sliding system.
This Penn Elcom double rack profile is 10U high and comes pre-drilled with holes at 15mm intervals for eased installation.
For eased gear-installation, this double rack profile from Penn Elcom features die-cut holes every 15mm and measures 14U in height.
Working on a custom flight case? Why not polish it off with this 30mm-high, anodised aluminium lid profile from Penn Elcom?
This Penn Elcom double rack profile is 4U high and comes pre-drilled with holes at 15mm intervals for eased installation.
This Penn Elcom double rack profile is 5U high and comes pre-drilled with holes at 15mm intervals for eased installation.
This Penn Elcom double rack profile is 12U high and comes pre-drilled with holes at 15mm intervals for eased installation.
This double rack profile from Penn Elcom comes with die-cut holes that have been spread 15mm apart for flexible gear installation. This model has a 16U height.
This Penn Elcom double rack profile is 18U high and comes pre-drilled with holes at 15mm intervals for eased installation.
A complete range, the Penn Elcom R8800 Series components can be assembled to build a fully customised anti-vibration rack mounting system, including this pre-drilled mounting panel.