▾

Behringer Europower EPX4000

No disponible, este producto ya no puede adquirirse.

No se han encontrado alternativas

Información del producto
Foto 360°
Opiniones (5)

Behringer Europower EPX4000
nº de producto: B-000-ABB Garantía Bax Music: Este producto tiene una garantía de 3 años (siempre y cuando se registre en la página de Behringer dentro de los 90 días siguientes a su adquisición). Si el producto no se registra, la garantía será de 2 años.

General

Power amplifiers have always been heavy. That makes sense, due to their large transformers and heat sinks. The new EPX amplifiers, however, are based on revolutionary switch-mode power supply technology. This means a heavy transformer is no longer required. Consequently, these amplifiers weigh 40% less than their conventional counterparts.

Europower EPX4000: ultra-lightweight and reliable
The EPX2800 and EPX4000 weigh no more than 10.1 kg. You could almost lift them with a single finger! Best of all, however, is the great reliability of these EPX amplifiers. They offer an even tighter bass reproduction than their predecessors, because they can handle high peak powers when required.

EPX amps: a class of their own
The secret to the amazing power/weight ratio of the EPX series is the use of a switch-mode power supply, combined with class-H topology. These amplifiers only work when required, instead of operating at full power continuously. As such, switch-mode powered amps are much more efficient than conventional power amps. They are smaller in size and lighter of weight too!

Sugerencias o comentarios sobre este producto -

Características

Peso y las dimensiones incluyen el paquete

Peso (incluyendo el paquete)	13,2 kg
Dimensiones (incluyendo el paquete)	48,7 x 30,1 x 15,2 cm

Características del producto

- amplifier
- 2x 2,000 Watt at 2 Ohm; 2x 1,200 Watt at 4 Ohm, 4,000 Watt at 4 Ohm (bridged)
- ATR (Accelerated Transient Response) technology
- ultra-lightweight with very little self-noise due to efficient switch-mode power supply
- switchable limiters with reliable overload protection
- detented gain controls
- precise LEDs for power, signal and limit
- XLR, 6.3 mm TRS and RCA input connectors
- professional speaker connectors and 'touch-proof' binding posts
- built-in subwoofer/satellite crossover
- independent DC and thermal overload protection on each channel
- 'back-to-front' ventilation system including air filter
- fully steel, 2U rack-mountable chassis
- RMS power stereo, 8Ohm per channel: 530 W
- RMS power stereo, 4 Ohm per channel: 870 W
- RMS power stereo, 2 Ohm per channel: 1,440 W
- RMS power bridged mono, 8 Ohm: 1,800 W
- RMS power bridged mono, 4 Ohm: 3,000 W
- peak power stereo, 8 Ohm per channel: 670 W
- peak power stereo, 4 Ohm per channel: 1,220 W
- peak power stereo, 2 Ohm per channel: 2,080 W
- peak power bridged mono, 8 Ohm per channel: 2,450 W
- peak power bridged mono, 4 Ohm per channel: 4,000 W
- controls front panel: power switch, input sensitivity (channel 1 and 2)
- control rear panel: crossover switch, mode switch, limiter switch
- indicator power: blue LED
- indicator limit (per channel): blue LED
- indicator signal (per signal): white LED (-20 dB, -10 dB, 0 dB)
- input connectors: balanced XLR, 6.3 mm TRS, RCA
- input sensitivity: 2.5 dBu
- input impedance: 10 kOhm unbalanced, 20 kOhm balanced
- output connectors: shielded binding posts, professional speaker connectors
- output circuitry type: class H
- distortion: < 0.05%
- frequency response: 20 Hz - 20 kHz, +0 / -1 dB
- amplification voltage: 35 dB
- damping factor: > 300 @ 8 Ohm
- signal/noise ratio: 100 dB
- cooling system: continuous fan with variable speed, back to front air flow
- amplifier protection: against short-circuiting, heat and HF
- overload protection: mute for on and off switching, switches off in case of DC defect
- power connector: standard IEC
- power consumption: 4,500 Watt
- operative voltage: 230 V ~, 50 Hz (T 15 A H 250 V)
- dimensions: 483 x 88 x 373 mm
- weight: 10.1 kg

Ya no se puede escribir una opinión sobre este artículo